European Commission - Growth

For a better experience, please enable Javascript!


Notification

Found : 45
 
  Body :

Laboratoire National de métrologie et d'Essais (LNE)
1, rue Gaston Boissier
75724 PARIS CEDEX 15
Country : France

Phone : +33 1 40 43 37 00
Fax : +33 1 40 43 37 37

Email : info@lne.fr
Website : www.lne.fr

Notified Body number : 0071

Version(s): 1 2 3 4 5 6 7 11 13 14 15 16 17 18 19 20 21 23 24

Last approval date : 24/04/2020
 

Return to legislation list

Some information about the accreditation details are available in the PDF
Legislation
2014/32/EU Measuring Instruments Directive    
Last approval date : 24/04/2020                 Version(s): 1 2

Products Procedures Articles/Annexes
Water Meters (Annex III MI-001)
Gas Meters and Volume Conversion Devices (Annex IV MI-002)
   - Volume conversion device (gas meter subassembly)
Active Electrical Energy Meters (Annex V MI-003)
Thermal Energy Meter (Annex VI MI-004)
   - Thermal Energy meter complete
   - Flow sensor (heat meter subassembly)
   - Temperature sensor pair
   - Calculator (type of temperature sensors)
EU type-examination
Conformity to type based on quality assurance of the production process
Conformity based on full quality assurance plus design examination
Annex II - Module B
Annex II - Module D
Annex II - Module H1
Measuring Instruments for Liquids Other than Water (Annex VII MI-005)
   - Fuel dispensers:
      - For liquids (other than liquified gases)
         - For liquified gases
   - Measuring systems on pipeline and systems for loading ships - all liquids
   - All other measuring systems [not stated elsewhere] – all liquids
   - Measuring systems on pipeline (accuracy class 0,3)
   - All measuring systems (accuracy class 0,5), in particular
      - fuel dispensers (not for liquefied gases)
         - measuring systems on road tankers for liquids of low viscosity (<20 mPa.s)
         - measuring systems for (un)loading ships and rail and road tankers
         - measuring systems for milk
   - measuring systems for refuelling aircraft
   - Measuring systems for liquefied gases under pressure measured at a temperature equal to or above -10* (accuracy class 1,0)
      - measuring systems normally in class 0,3 or 0,5 but used for liquids whose temperature is less than -10*C or greater than 50*C
         - measuring systems normally in class 0,3 or 0,5 but used for liquids whose dynamic viscosity is higher than 1 000 mPa.s
         - measuring systems normally in class 0,3 or 0,5 but used for liquids whose maximum volumetric flowrate is not higher than 20 L/h
   - Measuring systems for liquefied carbon dioxide (accuracy class 1,5)
      - measuring systems for liquefied gases under pressure measured at a temperature below -10*C (other than cryogenic liquids)
   - Measuring systems for cryogenic liquids (temperature below -153*C) – accuracy class 2,5
EU type-examination
Conformity to type based on quality assurance of the production process
Conformity based on unit verification
Conformity based on full quality assurance plus design examination
Annex II - Module B
Annex II - Module D
Annex II - Module G
Annex II - Module H1
Automatic Weighing Instruments (Annex VIII MI-006)
EU type-examination
Conformity to type based on quality assurance of the production process
Quality assurance of the production process
Conformity to type based on instrument quality assurance
Conformity based on unit verification
Conformity based on full quality assurance plus design examination
Annex II - Module B
Annex II - Module D
Annex II - Module D1
Annex II - Module E
Annex II - Module G
Annex II - Module H1
Taximeters (Annex IX MI-007)
EU type-examination
Conformity to type based on quality assurance of the production process
Conformity based on full quality assurance plus design examination
Annex II - Module B
Annex II - Module D
Annex II - Module H1
Material Measures (Annex X MI-008)
   - Material measure of length
EU type-examination
Conformity to type based on quality assurance of the production process
Quality assurance of the production process
Conformity based on unit verification
Conformity based on full quality assurance
Annex II - Module B
Annex II - Module D
Annex II - Module D1
Annex II - Module G
Annex II - Module H
Material Measures (Annex X MI-008)
   - Capacity serving measures
Internal production control plus supervised instrument checks at randoms intervals
EU type-examination
Conformity to type based on quality assurance of the production process
Quality assurance of the production process
Conformity to type based on instrument quality assurance
Quality assurance of final instrument inspection and testing
Conformity based on full quality assurance
Annex II - Module A2
Annex II - Module B
Annex II - Module D
Annex II - Module D1
Annex II - Module E
Annex II - Module E1
Annex II - Module H
Dimensional Measuring Instruments (Annex XI MI-009)
   - Length measuring instruments
      - for mechanical or electromechanical instruments
EU type-examination
Conformity to type based on quality assurance of the production process
Quality assurance of the production process
Conformity to type based on instrument quality assurance
Quality assurance of final instrument inspection and testing
Conformity based on unit verification
Conformity based on full quality assurance
Conformity based on full quality assurance plus design examination
Annex II - Module B
Annex II - Module D
Annex II - Module D1
Annex II - Module E
Annex II - Module E1
Annex II - Module G
Annex II - Module H
Annex II - Module H1
Dimensional Measuring Instruments (Annex XI MI-009)
   - Length measuring instruments
      - for electronic instruments or instruments containing software
EU type-examination
Conformity to type based on quality assurance of the production process
Conformity based on unit verification
Conformity based on full quality assurance plus design examination
Annex II - Module B
Annex II - Module D
Annex II - Module G
Annex II - Module H1
Dimensional Measuring Instruments (Annex XI MI-009)
   - Area measuring instruments
      - for mechanical or electromechanical instruments
EU type-examination
Conformity to type based on quality assurance of the production process
Quality assurance of the production process
Conformity to type based on instrument quality assurance
Quality assurance of final instrument inspection and testing
Conformity based on unit verification
Conformity based on full quality assurance
Conformity based on full quality assurance plus design examination
Annex II - Module B
Annex II - Module D
Annex II - Module D1
Annex II - Module E
Annex II - Module E1
Annex II - Module G
Annex II - Module H
Annex II - Module H1
Dimensional Measuring Instruments (Annex XI MI-009)
   - Area measuring instruments
      - for electronic systems or systems containing software
EU type-examination
Conformity to type based on quality assurance of the production process
Conformity based on unit verification
Conformity based on full quality assurance plus design examination
Annex II - Module B
Annex II - Module D
Annex II - Module G
Annex II - Module H1
Dimensional Measuring Instruments (Annex XI MI-009)
   - Multi-dimensional measuring instruments
      - for mechanical or electromechanical instruments
EU type-examination
Conformity to type based on quality assurance of the production process
Quality assurance of the production process
Conformity to type based on instrument quality assurance
Quality assurance of final instrument inspection and testing
Conformity based on unit verification
Conformity based on full quality assurance
Conformity based on full quality assurance plus design examination
Annex II - Module B
Annex II - Module D
Annex II - Module D1
Annex II - Module E
Annex II - Module E1
Annex II - Module G
Annex II - Module H
Annex II - Module H1
Dimensional Measuring Instruments (Annex XI MI-009)
   - Multi-dimensional measuring instruments
      - for electronic instruments or instruments containing software
EU type-examination
Conformity to type based on quality assurance of the production process
Conformity based on unit verification
Conformity based on full quality assurance plus design examination
Annex II - Module B
Annex II - Module D
Annex II - Module G
Annex II - Module H1
Exhaust Gas Analysers (Annex XII MI-010)
EU type-examination
Conformity to type based on quality assurance of the production process
Conformity based on full quality assurance plus design examination
Annex II - Module B
Annex II - Module D
Annex II - Module H1